Publication VDI: Influenz of oil drain holes

The oil emission of an internal combustion engine has a direct influence on the CO2 and particle emissions. As a result, the reduction of oil emissions, especially in the context of the stricter emission limits for the automotive industry, is increasingly becoming the focus of attention. To achieve this goal, a deeper understanding of the mechanism of action for the formation of oil emissions in internal combustion engines is necessary.
2016, Papadopoulos, Frommer, Künzel

Read More Publication VDI: Influenz of oil drain holes

Publication MTZ: Lube oil balance at the piston group

The investigation of the lubricating oil balance at the piston group and its influencing variables are an important contribution to optimizing future engine concepts in terms of consumption and emissions. At the Institute for Internal Combustion Engines of the Technical University of Munich, a novel engine was developed as part of the FVV project “piston ring oil transport 1″…
2016, Uhlig, Kirner, Behn, Feindt

Read More Publication MTZ: Lube oil balance at the piston group

Publication SAE: Piston ring pack fuel transport

The limitation of fuel entry into the oil sump of an internal combustion engine during operation is important to preserve the tribological properties of the lubricant and limit component wear. For observationand quantification of the effects leading to fuel entry, a highly sensitive and versatile measurement system is essential. While oil sampling from the sump followed by laboratory analysis is a common procedure, there is no system for automatic sampling of all the positions and fast online analysis of the samples.
2015, Behn, Feindt, Matz, Krause, Gohl

Read More Publication SAE: Piston ring pack fuel transport

Publication FVV: OIL DILUTION FUEL-OIL-INTERACTION

The aim of the research cluster “Fuel in Oil” is the investigation and quantification of the interaction between the fuel and the lubrication oil caused by late post injections, which are applied for the regenerationof the particulate filter or the NOx storage catalyst. To achieve the objectives, different phenomena like the fuel entry into the lubrication film, the fuel-oil transport by means of the piston rings, the evaporation of fuel out of the oil pan and the impact of the oil separator of the oil dilution were…
2015, Seel, Geppert, Meister, Ehrly, Behn, Feindt, Bregar, Lyubarskyy, Oliva

Read More Publication FVV: OIL DILUTION FUEL-OIL-INTERACTION

Publication MTZ: Particles, Oil Emission, pre ignition

Modern downsizing in connection with the future more rigorous exhaust limit values for cars, commercial vehicles and off-highway applications, is a great challenge for internal combustion engine systems and components. In this context, increased oil emission leads to increased particle and HC emissions. Additionally, the efficiency of the exhaust gas aftertreatment and the pre-ignition…
2014, Hadler, Lensch-Franzen, Gohl, Mink

Read More Publication MTZ: Particles, Oil Emission, pre ignition

Publication SIMEA: Oil emission, dynamic and static test

Exemplary results in this paper reveal that knowledge about steady-state LOC is one important element but not sufficient for further LOC reduction on modern engines. Besides the general influence of speed and load during steady-state operation LOC behavior is affected by dynamically induced LOC mechanisms, which can contribute significantly to overall LOC. As a result, optimum engine component development includes evaluation of LOC behavior for stedy-state and dynamic engine operation.
2012, Frommer, Beeckmann, Freier, Pierotti

Read More Publication SIMEA: Oil emission, dynamic and static test

Publication SAE: Mixture formation, Influence on oil emission

Partly competing objectives, as low fuel consumption, low friction, long oil maintenance rate, and at the same time lowest exhaust emissions have to be fulfilled. Diminishing resources, continuously reduced development periods, and shortened product cycles yield detailed knowledge about oil consumption mechanisms in combustion engines to be essential. There are different ways for the lubricating oil to enter the combustion chamber…
2010, Gohl, Brandt, Wittler, Budde, Krause, et al.

Read More Publication SAE: Mixture formation, Influence on oil emission